Using the Chilipepper Model CP8000RC removes the need for running gallons of water down the drain while waiting for hot water. At the touch of a button, hot water is pumped from the water heater to the sink or shower. Once the Chilipepper detects that the hot water has arrived, it turns itself off. The temperature sensor is adjustable with 4 temperature settings. The Remote Operation System is integrated right into the circuitry of the Chilipepper so it doesn't require any extra set-up. It comes with 2 prepared to use Key-Fob-Style Controllers. The Remote Operation System is available in 2 separate codes for those customers who want more than one pump in their home. The keyfobs are color-coded to distinguish them. Cream colored Key-Fobs are Remote Code #1, Brown colored Key-Fobs are Remote Code #2. Intended for the do-it-yourselfer, the Chilipepper is easy to install and comes with everything you need (except two stainless steel adaptable hoses that may be bought at any hardware store). Get fast hot water and save time, water, and money.
Bell & Gossett 103405LF Low Lead 1/6 HP NBF-45 3-Speed Bronze Circulator Pump Material: Bronze Amperage: 2. 3 Application: Heating Voltage: 115V Max psi: 150 psi Type: Pump Horse Power: 1/6 Connection Size: 1" X 1-1/4" X 1-1/2" Flow Range: 0-44 GPM Head Range: 0-27 ft. Hertz: 60 Phase: 1 RPM: 3300 Temperature Range (F): 40 degrees F to 225 degrees F Connection Type: Flanged.
The Aquatec ERP-1000 Permeate Pump is a non-electrical device that uses only the hydraulic energy of the 'brine water' (usually lost down the drain) to push extra purified water ('permeate') into your pressure tank. This is a great eco-friendly add-on. Increase your RO efficiency as much as 400 %.
Condensate elimination Pump, VCMA-15UL Is completely auto With 1/2 Gallon Capacity, Features A Vertical Type Pump With Stainless Steel Motor Shaft, Rust evidence, High affect ABS Tank & Motor Cover, 3 Drain Holes, Removable 3/8" OD Barbed Check Valve, Rated For High Efficiency Gas Furnace Applications That Produce An Acidic Condensate, Thermally Protected Motor, UL & CSA Listed, Pumps 25 GPH @ 10' TDH.
The Aqua-Flo Flo-Master HP and CP P382LE51 Series Pumps are perfect for spas and hot tubs with some number of jets since they frequently require a greater output. The remaining flow rates of the Flo-Master let the pump to run at a lower hp to do the same job of higher hp pumps. Using less hp means a lower operating cost and more money in your pocket! AquaFlo part number FMCP 02610000-1010 FMCP - Center Discharge Ideal for bigger, multi-jet tubs or alike applications that require greater output. Fast release compression fittings let for easy installation or maintenance. Compact, unitized, single spring elastomer bellows mechanical seal offers maximum durability and performance. High-performance impeller which gives flow rates that surpass all tested competition. Drip evidence, cool running seal virtually removes seal burnout Adapts to a hair and lint trap for self priming applications Stainless steel fasteners Unions are included 1. 5" Inlet and outlet plumbing connections Operational hp: 1 HP Total hp: 1. 5 THP 115 Volt 2 Speeds Replaces the following pump models: 02610516-2 03610000 02610000-1 03510631-2 The Aqua-Flo Flo-Master FMCP Pump has a center discharge on the top of the pump and the FMHP Pump has an side or offshoot discharge. Flo-Master Pumps come complete with fast release compression fittings which makes installation and maintenance simple. The upgraded shaft seal and high performance impeller help to offer a high level of performance in any condition.
Aqua-Flo by Gecko's Circ-Master pump takes 24-hour filtration to a new level, delivering the highest GPM of any recirculation pump on the spa business. Higher GPM lets the Circ-Master to operate a high-flow heating system ensuing in increased heating efficiency and up to four times the filtration. The Circ-Master also operates standard low-flow heating systems with increased dependability caused by:& & • & & 48 frame, uninterrupted-responsibility construction with front and rear, permanently lubricated ball bearings for expanded motor life. & & • & & Carbon-graphite self-lubricating seal intended for uninterrupted responsibility operation. & & • & & 1 1/2" inlet and outlet. & & • & & fast release compression fittings let for easy installation or maintenance & & • & & Available in side discharge and center discharge models.
The Wayne T100S10-2 deep well submersible pump is intended for well depths of 20-feet to 300-feet deep. This pump is made with corrosion-tolerant stainless steel motor enclosure, pump shell and fasteners. Intended with heavy-responsibility thermoplastic impellers, diffusers, intake screen and check valve. The high efficiency, hermetically sealed motor is thermally protected to prevent overheating.
This cast iron centrifugal pump and motor assembly, comes with 0. 5 hp, single phase, ODP (Open Drip evidence) electric motor. This heavy-responsibility motors, easy service design and four-position discharge. All models include replaceable wear ring and feature back pull-out design. Gives for easy winterizing and close grained cast iron. It's use in water systems and sprinkling for homes, farms and business. It measures 1-1/4-inch by 1-inch NPT ports.
Goulds EP0411A 4/10HP, 115V Submersible Effluent Pump, 3/4" Solids, 12 Amps, Piggyback/ large-Angle Float Switch FEATURES Thermoplastic semi-open design with pump out vanes for mechanical seal protection. Casing and Base: Rugged thermoplastic design gives superior strength and corrosion resistance. Motor Housing: Cast iron for economical heat move, strength, and durability. Motor Cover: Thermoplastic cover with integral handle and float switch attachment points. Power Cable: serious responsibility rated oil and water tolerant. Bearings: Upper and lower heavy responsibility ball bearing construction. APPLICATIONS exactly intended for the following uses: Effluent systems Homes Farms Heavy responsibility sump Water move Dewatering plans Solids handling capability: 3/4" maximum. Capacities: up to 60 GPM. Total heads: up to 31 feet. Discharge size: 11/2" NPT Mechanical seal: carbon-rotating/ceramic-stationary, BUNA-N elastomers. Temperature: 104 F (40 C) uninterrupted 140 F (60 C) intermittent. Minimum Circuit Breaker: 20 Class B Insulation Fasteners: 300 series stainless steel able of running dry without damage to parts. Motor: Single phase: 0. 4 HP, 115 V, 60 Hz, 1550 RPM, fitted overload with auto reset. Power cord: 10 foot standard length, 16/3 SJTW with three prong grounding plug. Completely submerged in high grade turbine oil for lubrication and economical heat move.
1/3 HP Residential Drain Pump with QuickTree Technology The short profile of Liberty's 404 is specially intended for compact regions and gives you the freedom to install fixtures where gravity drain lines aren't available. Our QuickTree Technology gives a separate access cover for easy switch inspection. For gray wastewater applications, the 404 is perfect for laundry tray sinks, bar sinks, washing machines and other basement remodeling projects. The system arrives completely assembled and prepared to install. Liberty Pump 404 Features: Factory pre-assembled and prepared to install completely auto operation Short profile design for compact regions Separate access cover for easy switch inspection QuickTree technology lets for fast inspections and elimination of float switch without disconnecting plumbing Integrally molded rubber gasket for a superior gas-tight seal Oil-filled, hermetically sealed motor with thermal-overload protection 10ft. 3 wire power cord with grounded plug Corrosion-tolerant polyolefin basin with molded-in connections Can handle 3/8" solids Maintenance-free, permanently lubricated sealed bearings Energy saving economical motor design decreases energy handling by up to 40% Liberty Pump 404 plans: Height: 11. 125" Width: 13. 75" group: Grey Water Connection Size: 1-1/2" Flow Rate (GPM): 35 Maximum Head Height: 20 Motor HP: 1/3 Maximum liquid Temperature(F): 140 Degrees Voltage: 115 V Weight: 19 lbs.
Wilo Top S Two Speed CI Pump 1. 5 x 30 115VSKU: 2067550This pump is made from mix of stainless steel, polypropylene and metal impregnated carbon. It is major feature is the 2 speed motor. This is a wet rotor - "seal less" design type pump. Great for residential and light commercial applicationsPermitted temperature range -20° C to +130° C, shortly-term operation (2h) to +140° CPre-selectable speed phases for manual capacity adjustmentPump communication depending on simple plug technology that may be reliably retrofittedCombination flanges PN6/ PN10 (DN 40 to DN 65)Cataphoretic coated pump housingThermal insulation shell as standardAutomatically VentedExtensible motor protection, signal and display functions1/4" suction and discharge gauge tappingsFor all hot-water heating systems, air-conditioning systems and closed cooling circuitsFlanges aren't inculded. Plans.
Grundfos UP15-29SUC/TLC is a 1/8HP Stainless steel Circulator Pump (Gundfos SKU# 59896777) with a removable Integral Check Valve, 1-1/4" (GU125) union connections, Timer and 6-foot Power Cord. Grundfos UP15-29SUC/TLC is perfectly suited for recirculation applications thanks to the fitted timer and needless wiring is eliminated by plugging the circulator directly into the electrical outlet. Stainless steel construction of the UP15-29SUC/TLC model lets to use it in applications like radiant, solar, hydronic, chilled water cooling, domestic hot water recirculation and many others.
The Wayne T50S10-4 deep well submersible pump is intended for well depths of 20-feet to 120-feet deep. This pump is made with corrosion-tolerant stainless steel motor enclosure, pump shell and fasteners. Intended with heavy-responsibility thermoplastic impellers, diffusers, intake screen and check valve. The high efficiency, hermetically sealed motor is thermally protected to prevent overheating.
With a reliable 208cc Powerhorse engine and silicon carbide mechanical seals that resist corrosion, wear and heat better than a regular seal, this Powerhorse water pump from Northern Tool gives you the performance you need, when you need it. Features a quality engine and quality parts intended to deliver years of service. Not for sale in California. Low Oil Shutdown: Yes, Flow (GPH): 7, 860, Max. Liquid Temp. (deg F): 98, Volute: Cast iron, Max. Suction Lift (ft. ): 23, hard Handling (in. ): 5/8, Engine: Powerhorse, Dimensions L x W x H (in. ): 22 x 18 x 17, Run Time: 2 hrs. Engine Displacement (cc): 208, Max. PSI: 43 1/2, Seals: Silicon carbide, Fuel Capacity (gal. ): 2 3/4, Suction Port (in. ): 2, Max. Total Head (ft. ): 98, Impellers: Cast iron, Fits Hose Dia. (in. ): 2, HP: 6, Discharge Port (in. ): 2.
PRO-SourceTM Water System Packages are useful and econom- ical pump/tank packages for the professional freelancer. The PRO-SourceTM Water System Packages use the NEW ProJetTM cast iron jet pumps and the reliable PRO-SourceTM quality Included in package is a 19 Gallon steel tank, 1/2 H. P. 1/115-208V pressure pump, Square D 30-50 pressure switch and pump-to-tank connection. Pressurized steel tanks. Plumbing connections are made using galvanized fittings and 3-ply nylon strengthened vinyl tubing with stainless steel hose clamps. Ideal for installations where there's restricted space.
The Grundfos Group is continually striving to preserve their position as one of the world's leading and most successful manufacturers of pumps for water supply, heating and waste water systems. The UPS1555SFC (59896773) major features of a SuperBrute is its 3speed motor, allowing you to change the pump speed based on your application. Flexibility to decide your speed gives you the peace of mind you have the correct pump for the job. For applications requiring stainless steel.
The MARS pump design couples business leading performance with the installation flexibility and features you have to get the job done. The fast release silicone check valve lets for fast and economical servicing without the have to remove the condensate line. The integrated safety switch may be wired for equipment shut down or straight to a high level alarm.